Autowatch Ghost Immobiliser Installation
The Ghost is the UK's most advanced aftermarket immobiliser for the CAN bus. It is discreet, does not use LED indicators or key fobs and is hidden within the vehicle's wiring.
The user can also deactivate the system for a short period of time by using Transport Mode when renting out their vehicle. This guide will guide you through the steps of installing a Ghost immobiliser.
Professional Installation
The Autowatch Ghost immobiliser is a advanced security device that safeguards your vehicle against hacking, key cloning, and relay attacks. The system connects directly to your vehicle's ECU and is protected by a unique pin code of your choice. It is inaccessible to thieves using diagnostic scanners or other advanced methods, and it is unable to be disabled by circuit cuts.
The system is simple to use, however professional installation is recommended to ensure a clean connection with the ECU of your vehicle. A certified installer from Thatcham can assist with the installation and programming of your Ghost system. They can also recommend a tracking system or alarm system to complete the protection package for your vehicle.
First, the installer must disconnect your battery in order to avoid the possibility of airbag deployment and short circuits. After that the installer is now able to begin work. Hand tools are the most basic to be used for precise connections. A multimeter is a great tool to verify electrical values. Cable ties and insulation tape are also vital for protecting connections and keeping wiring neat. The Ghost Immobiliser user's guide will provide specific instructions specifically tailored to your specific model.
It is essential to choose a grounding location that is free of paint or debris during installation. The installer must ensure that the immobiliser's CAN H as well as CAN L wires are connected to the correct ports on the vehicle's ECU. Based on the model, these wires could need to be soldered or plugged in. A high-quality connector is recommended to ensure a sturdy and secure connection.
Once the installation is complete Once the installation is completed, the customer can enable the Transport Mode. This allows mechanics or valet parking to use the vehicle, without knowing the pin code. To accomplish this, the user must press the button for service on the dashboard five times within 2 seconds. After ghost 2 immobiliser cost is done the system will verify with 5 indication signals.
The Autowatch Ghost 2 immobiliser is TASSA approved and is a highly efficient immobiliser. It's a great choice for those who rent out their vehicles regularly on platforms such as Turo. Immobilisers can lower insurance costs, since it reduces the risk of theft.
Getting Started
You can't go far wrong with an autowatch ignition device for those who want to safeguard your vehicle from theft. The device stops your car from running even the case that someone steals or copies your key. It's possible because of its advanced technology that stops the engine from starting until the right PIN code is entered.
The device connects to the vehicle's CAN bus network and allowing it to communicate with the ECU directly. It uses the buttons on your steering wheel and dashboard to create a unique sequence that only you can understand. This makes it impossible for anyone else to start your vehicle. This is the most secure security system that protects your most precious possessions and preserve its value when you want to sell it in the future.
Installing a Ghost immobiliser is easy, but you must follow the directions to avoid electrical problems and malfunctions in the system. You'll need to locate a 12V power supply and a suitable grounding for the car's chassis. After that, you can begin connecting the wires for the immobiliser. Use high-quality connectors and soldering techniques to ensure a solid connection. Insulate the connections using heat shrink tubing or insulation tape, or other materials to prevent short circuits of electricity.
Once the wires have been connected, you can plug in the battery and begin the engine to check whether the immobiliser works. After you've verified that everything is functioning properly, you can install the immobiliser in a secure place inside the vehicle. Make sure to hide it well to prevent any thief from taking advantage of it.
The Ghost 2 immobiliser is TASSA (Tracker and Aftermarket Security System Association) certified, which means that it meets the highest standards of security and is an excellent deterrent to car thieves. It is resistant to hacking and key cloning and cannot be disabled without a code. The device is easy to use and can be set into a service valet setting so that your vehicle won't be activated when you take it for an MOT or service.
Wiring
The Ghost Immobiliser is a cutting-edge security system that is designed to stop theft of vehicles. It communicates with your vehicle's ECU and directly connects to its CAN bus. Unlike other aftermarket systems that require the removal of circuit components, the Ghost Immobiliser doesn't interfere with the factory settings for your vehicle.
The system is also unnoticeable by thieves using diagnostic scanners. This is due to the fact that it doesn't transmit and receive radio frequency signals and it uses CAN data to communicate with your ECU. It also doesn't require modifications to your current key fobs.
Enter the sequence to disarm (either two or one button) and turn on the ignition in your car to use Ghost Immobiliser. The indicator will flash twice to verify that you've entered the correct code. Once you've verified this, you're able to start your vehicle and drive off in peace.
Once installed The Ghost Immobiliser can safeguard your vehicle from key cloning and hacking, while protecting the value of your pride and joy. In Transport Mode, you can temporarily disable the Ghost Immobiliser when you need to hand your vehicle to service or valet parking.
To complete the Ghost Immobiliser installation, you'll need identify the source of power that is constant (12V) and an earthing point. Make sure that both are well-insulated and able to be touched. Cable ties are also recommended for bundling and secure the wires. This reduces the possibility of theft by thieves. To avoid making mistakes, make sure to double-check these points and mark them with a label or tape. Examine every connection for signs that they're getting worn out. Connections that are loose can cause malfunctions in the system, so make sure they're securely fixed and well-insulated. Finally, don't forget to test the Ghost Immobiliser after installation is completed. This will ensure that the unit functions properly and that all connections and insulation are safe. Make sure to address any issues immediately.
Testing
The Autowatch Ghost immobiliser is a revolutionary vehicle security system that works seamlessly with your car's ECU to prevent unauthorized motor starting. Its innovative technology protects your car from hacking, key cloning, and other methods that thieves employ to steal vehicles. The Ghost is a perfect complement to existing tracking and alarm systems to provide the most effective security for your vehicle. The Ghost's unique features and secluded design make it a popular option for car enthusiasts and security-conscious drivers too.
In order to ensure that the Ghost Immobiliser is properly integrated the Ghost Immobiliser, you must to follow every step of the installation procedure. Consult the wiring diagram of the vehicle as it will aid you in locating and connecting the wires. You'll then need to identify the grounding and power sources. Once you have located them, you will be required to mark the points so that they are easy to locate during installation. It's essential to use high-quality materials and tools. Basic hand tools can aid in making precise connections. A multimeter will check electrical values, and also ensure security. Insulation tape and cable tie will ensure that all connections are tidy. Additionally, a user's manual will provide specific guidance specifically tailored to your Ghost model.
Before proceeding with the installation it is important to test the system by entering the PIN code, then starting the vehicle. This test will verify that the immobiliser works as intended and will stop vehicle starts that are not authorized. This step should be done frequently as part of your regular inspections of the vehicle to ensure the system is always functioning properly.
Once the installation is complete After the installation is completed, you are able to drive your car with confidence. The Ghost will keep your pride and joy safe from would-be thieves and ensure that no one can take off with your vehicle without the correct PIN code. The Ghost can be paired with an approved Thatcham tracker, which detects attempts to steal or tamper with. This will allow you to locate your car if it's stolen.
The Ghost is compatible with a range of automobiles, including those from most major manufacturers. If you are looking to secure your vehicle using this advanced device, contact Monty's Locksmith today to find out more about our installation and service options. We are a TASSA registered installer, which ensures that we adhere to strict standards for installing our products. This assures customers, insurance companies and law enforcement officials that all installations are completed safely and in a correct manner.